The appearance of the product may differ from the illustrations presented in this manual.
This manual is designed for study the main technical characteristics, operating principle and rules of technical operation of a coating machine 27 kg.
Before use carefully read the instructions below!
Improper use of the equipment can be a source of danger. By starting work with the device you confirm that you are fully acquainted with this manual and understood the rules of operation of the device.
KADZAMA Ltd appreciates your purchase and wishes you a pleasant work experience.
Coating machine 27 kg is designed for «rolling» various substances on nuts, peanuts and other loose goods.
Power supply, [V] / [Hz] | 220 / 50 |
Power intake (not more than), [kW] | 0,55 |
Loading capacity, [kg] | 27 |
Bowl rotation speed, [rev / min] | 0 — 90 |
Dimensional size (L x W x H), [mm] | 750 х 920 х 1200 |
Weight, [kg] | 125 |
Coating machine 27 kg — 1 pc.
Manual — 1 pc.
Warranty card — 1 pc.
4.1. Coating machine is an electric appliance with a certain danger potential. When connecting the device to the electric grid, take all necessary precautions to avoid electric shock.
4.2. Coating machine must be connected to the power supply and operated only by trained personnel.
4.3. It is not allowed to operate coating machine in the absence of electrical grounding («E» wire).
4.4. Coating machine should be used only for its intended purpose.
4.5. Use and store coating machine in a place out of reach of children
4.6. Do not leave coating machine switched on without supervision for a long time.
4.7. Do not operate coating machine with wet hands.
4.8. Do not allow liquids inside coating machine through the vents of the device.
4.9. Do not use coating machine at ambient temperatures below 10˚C and above 40˚C, and relative humidity above 80%.
4.10. When transporting coating machine at sub zero temperatures, prior to first use it should be kept at room temperature for at least 1 hour.
4.11. Any maintenance should be carried out when coating machine is disconnected from the power supply!
4.12. Repair or disassembly of coating machine may only be provided with the assistance of qualified personnel of KADZAMA Ltd.
1 — Base
2 — Swing frame
3 — Bowl
4 — Handwheel
5 — Control block
6.1. Remove the packaging.
6.2. Set coating machine on a flat hard surface, providing easy access to controls.
6.3. Make sure that the distance between the body and the nearest objects is at least 10 cm, make sure the air vents are not blocked.
6.4. Fix the wheels with wheel clips.
6.5. Plug the equipment into a 220V power supply.
7.1. Coating Machine 27 kg is ready to work, switch it on using the circuit breakers (1) located at the back of the control block. Make sure the emergency stop button (5) is not activated (if it turned on — turn off by rotating it clockwise).
Rear | Front |
1 — Circuit Breakers
2 — START button
3 — STOP button
4 — Rotary speed control knob
5 — Emergency stop button
7.2. Operate the main drive using the START / STOP buttons. Place the required amount of loose product (nuts) in the bowl.
7.3. Pour a thin stream of, for example, glaze in a bowl. Rolling over the surface of the bowl, nuts are evenly glazed. You can pour the glaze again in a while and repeat this operation until the nuts acquire a sufficient layer. The round shape is formed gradually, as the layers of the glaze grow.
7.4. To obtain a smooth and a high-quality glaze layer, it must be cooled quickly. After the glaze has solidified on the nuts, the process will continue without sticking to the bowl and won’t interfere with the mixing of the dragees in coating machine. The air conditioner installed in the room can significantly reduce the time of coating.
7.5. After obtaining the layer you need, a glossier and various powders (for example, kandurin) can be added in order to improve the aesthetic appearance of the products.
7.6. After finishing work, the ready product must be removed from the bowl. To do it, tilt the swing frame with the handwheel (4).
8.1. During the operation keep coating machine clean.
8.2. It is allowed to wipe coating machine with a damp cloth, after disconnecting it from the power supply.
8.3. It is allowed to clean the bowl under warm water and wash with detergents. After washing, the bowl should be wiped dry.
8.4. Water is not allowed inside the control block.
The warranty period (as well as the terms of warranty service) are specified in the warranty card.